For all the "Rite" Loading Dock Solutions

• Counter Doors
• Counters w/Sill,Trim
  •  Push-up Operated
    •  CDF Aluminum
    •  CDF Steel
    •  CDF Stainless Steel
  •  Crank Operated
  •  Motor Operated
• Wood Counter Doors
• Grilles
• Side Coiling Closures

• View current newsletter (PDF)
• 
  Enter your email address below
  to subscribe to our newsletter.

CDF Push-up Operated
Steel Counter Door With Seal & Trim

Mounting:  Between jamb mounted

Maximum Size:  10’4” wide X 6’4” high

General:

• Materials furnished with all Steel Rolling Counter Doors with Sill & Trim include all curtains, bottom bars, guides, brackets, hoods, operating mechanisms and any special features.
• All Steel Rolling Counter Doors with Sill & Trim are designed to a standard maximum of 10 cycles per day and an overall maximum of 20,000 operating cycles for the life of the door.

Materials

• The door curtain is constructed of interconnected No. 10 (1¼” high by ⅜” deep) 22 gauge galvanized steel slats.
• The bottom bar is constructed of tubular extruded aluminum measuring 15⁄16” deep by 2¼” high with a double vinyl astragal on the bottom edge
• The integral door frame and guides are constructed of 16 gauge stainless steel at the head and jambs and 14 gauge stainless steel at the sill.
• The sill extends 4” on either side of the wall.
• All frame joints are flush and smooth.
• The brackets are constructed of 3⁄16” thick die cast aluminum.
• The barrel is steel tubing of not less than 4” in diameter.
• Oil tempered torsion springs are capable of correctly counter balancing the weight of the curtain.
• The barrel is designed to limit the maximum deflection to .03” per foot of opening width.
• The hood is fabricated from 24 gauge stainless steel and is formed to fit the square brackets.

Finish:

• The finish on the integral frame (head, jambs and sill) and on the hood  is #4.
• The finish on the barrel is one (1) coat of bronze rust-inhibiting prime paint.
• ColorCote:
  The curtain and bottom bar have a ColorCote finish.  ColorCote consists of the following:
  1. Hot dipped galvanized G-90 coating consistent with ASTM A-653
  2. Bonderized coating for prime coat adhesion
  3. Factory applied Thermosetting Powder Coating applied with a minimum thickness of 2 mils. The color is selected by the architect and is chosen from [standard color charts] [custom color selection].
  The ColorCote finish is such that there is no corrosion
  when the material is subjected to salt spray resistance test
  ASTM B-117 for 1000 hours.
• FinalCote:
  The curtain, bottom bar, guides and hood will have a FinalCote finish. FinalCote consists of the following:
  1. Hot dipped galvanized G-90 coating consistent with ASTM A-653
  2. Bonderized coating for prime coat adhesion
  3. Corrosion inhibiting primer - .2 mils per side
  4. Thermo-setting tan polyester top coat with a minimum thickness of .6 mils each side

Operation

• Push-up operated doors open and close with a maximum of 30 pounds of effort utilizing finger lifts in the bottom bar. This type of operation should not be used for doors over 10 feet wide.

Locking Mechanisms

• The push-up doors are secured by means of a concealed sliding bolt deadlock in the bottom bar operated by a [thumbturn] [cylinder lock].

Installation

• All-Rite Steel Rolling Counter Doors with Sill & Trim must installed by an authorized All-Rite representative.

Warranty

• All-Rite Steel Rolling Counter Doors with Sill & Trim are warranted for a period of 2 years from the time of shipment against defects in workmanship and materials.